| 1 Scope范围 |
| 2 Normative Reference规范性引用文件 |
| 3 Terms,Definitions,Acronyms,and Abbreviations术语、定义和缩略词 |
| 3.1 Terms and Definitions术语和定义 |
| 3.2 Acronyms and Abbreviations缩略词 |
| 4 General总则 |
| 4.1 Unit Responsibility机组责任 |
| 4.2 Classification and Designation分类和名称 |
| 5 Requirement要求 |
| 5.1 Unit单位制 |
| 5.2 Statutory Requirement法规要求 |
| 5.3 Hierarchy of Requirement优先级要求 |
| 6 Basic Design基本设计 |
| 6.1 General总则 |
| 6.2 Pump Type泵型 |
| 6.3 Pressure Casing压力泵壳 |
| 6.4 Nozzles and Pressure Casing Connections管口和压力泵壳接口 |
| 6.5 External Nozzle Forces and Moments作用在管口上的外力和外力矩 |
| 6.6 Rotors转子 |
| 6.7 Wear Rings and Running Clearances耐磨环和运转间隙 |
| 6.8 Mechanical Shaft seals机械密封 |
| 6.9 Dynamics动力学 |
| 6.10 Bearings and Bearing Housings轴承和轴承箱 |
| 6.11 Lubrication润滑 |
| 6.12 Materials材料 |
| 6.13 Nameplates and Rotation Arrows铭牌和转向牌 |
| 7 Accessories辅助设备 |
| 7.1 Drivers驱动机 |
| 7.2 Couplings联轴器 |
| 7.3 Guard联轴器罩 |
| 7.4 Baseplates底座 |
| 7.5 Instrumentation仪表 |
| 7.6 Piping and Appurtenances管路和附件 |
| 7.7 Special Tools专用工具 |
| 8 Inspection,Testing,and Preparation for Shipment检查、试验和发货准备 |
| 8.1 General总则 |
| 8.2 Inspection检查 |
| 8.3 Testing试验 |
| 8.4 Preparation for Shipment发货前的准备 |
| 9 Specific Pump Types特定泵型 |
| 9.1 Single-stage Overhung Pumps单级悬臂泵 |
| 9.2 Between-bearings Pumps (Types BB1, BB2, BB3, and BB5)两端支承泵（BB1，BB2，BB3 和BB5 型） |
| 9.3 Vertically Suspended Pumps (Types VS1 Through VS 7)立式悬吊泵（VS1~VS7 型泵） |
| 10 Vendor’s Data卖方数据 |
| Annex A (normative) Specific Speed and Suction-specific Spped附 录 A （资料性附录） 比转速和汽蚀比转速 |
| Annex B (normative) Cooling Water Schematics附 录 B （规范性附录） 冷却水示意图 |
| Annex C (normative) Hydraulic Power Recovery Turbines附 录 C （规范性附录） 液力回收透平 |
| Annex D (informative) Standard Baseplates附 录 D （规范性附录） 标准底座 |
| Annex E (informative) Inspector's Checklist附 录 E （资料性附录） 检查员检查清单 |
| Annex F (normative) Criteria for Piping Design附 录 F （规范性附录） 管路设计准则 |
| Annex G (informative) Materials Class Selection Guidance附 录 G （资料性附录）材料等级选择导则 |
| Annex H (normative) Materials and Material Specifications for Pump Parts附 录 H （规范性附录） 泵零部件材料及材料技术要求 |
| Annex I (normative) Lateral Analysis附 录 I （规范性附录） 横向分析 |
| Annex J (normative) Determination of Residual Unbalance附 录 J （规范性附录） 残余不平衡量的确定 |
| Annex K (informative) Shaft Stiffness and Bearing System Life附 录 K （资料性附录） 轴的刚度和轴承系统的寿命 |
| Annex L (informative) Contract Documents and Engineering Design Data附 录 L （资料性附录）轴的刚度和轴承系统的寿命 |
| Annex M (informative) Test Data Summary附 录 M （资料性附录） 试验数据一览表 |
| Annex N (informative) Pump Data Sheets and Electronic Data Exchange附 录 N （资料性附录）泵数据单和电子数据交换 |
| Annex O (informative) Special-purpose Centrifugal Pumps附录 O （资料性附录）特殊用途离心泵 |
| Bibliography参考文献 |